ALLOY X

ALLOY800H/HT (Incoly800HT)

Characteristics
Corrosion Resistance
Applications
Chemical Composition
Mechanical properties
International Standard Comparision Chart Stock Form And Sizes
Round Bars
Hex Bars
Nuts And Washers
Spring Washer
Hex Bolt
Stud Bolt
Flanges
Sourceable Materials

Characteristics

ALLOY800 HT is an austenitic high-strength solid-solution Ni-Fe-Cr Alloy with controlled levels of C, Al, Ti, Si and Mg and increased content of (Al + Ti).
A special solution anneal treatment gives highest creep-rupture strength above 700 °C (1290 °F) due to the precipitation of TiC.
Below 700 °C (1290 °F), gamma prime (γ´) precipitates combined with loss of ductility.

  • excellent creep strength at temperature above 700 °C (1290 °F)
    good resistance to reducing, oxidizing and nitriding atmospheres and to atmospheres which alternate between reducing and oxidizing conditions
    metallurgical stability in long-term application at high temperatures
    For applications where frequent excursions to temperatures lower than 700 °C (1290 °F) during service cannot be excluded or parts of the material are permanently exposed to a temperature below 700 °C (1290 °F), the use of ALLOY800H is recommended.
Density8.44

Stock Form and Sizes

※ ◆1000㎜ ◎2000㎜ ▲3000㎜ ■3500㎜ ●4000㎜ ★2500㎜~3990㎜

Round Bars Specification: ASTM B408/B564※ ASME SB408/SB564※ ※B564/SB564 Apply to Forged Bar Only

Stock Specification:800H/HT Dual

size 1〜13
1.2 1.6 2 2.6 3 3.5 4 4.4 5 5.3 6 7.1 8 8.95 10 12 12.7
                           
size 16〜50
16 18 19 20 22 24 25 28 30 32 35 36 38 40 42 45 50
       
size 55〜135
55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135
       
size 140〜300
140 145 150 160 165 170 180 190 200 210 220 230 250 280 300    
                   
Hex barsSpecification:ASTM B446
10 13 14 17 19 21 22 24 26 27 30 32 36
                   
Nuts and washersSpecification:Nuts JIS B1181 Class1 Washers / JIS B1256 Normal Series Grade.A
M5 M6 M8 M10 M12 M16 M20
       

※Please enquire about grades and sizes not in stock.

Sourceable Ex-Stock Material for other Forms from Distributors World-Wide

Equivalent Round Bars Plate Pipe/Tube Welding Rod & Wire
Min Max Min Max
Incoly800HT 12.7~203.2 0.51~50.8

*○: Various sizes available in stock. △: Only limited sizes available in stock. ☆: Please contact us for more details.
* We can supply materials and products that comply with various standards including ASTM, ASME, AMS, and NACE standards. Please contact us for more details.

Corrosion resistance

The high nickel and chromium contents of Alloy800H/HT ensure excellent resistance to oxidation.
The alloys are also very resistant to carburization, nitridation and oxidizing sulphur-bearing atmospheres.
The protective oxide film which is formed is adherent in both static and cyclic conditions of heating and cooling, and resistance to carburization is enhanced when a thin film of oxide is formed on the alloy through pre-oxidation prior to service.
Resistance to hydrogen is excellent and Alloy800H/HT are standard materials used in the production of hydrogen in steam/hydrocarbon reforming processes.

Applications

Due to high strength during long periods of service and resistance to carburization and nitridation, ALLOY800H/HT have found many applications in steam/hydrocarbon reforming for components such as: pigtails, headers/collectors/manifolds, transfer piping, catalyst tubes (in lowpressure processes) and quench-system piping.

Typical applications are:
  • ethylene pyrolysis tubing in convection and radiant sections – resistance to carburization and good mechanical properties
  • ethylene dichloride cracking tubes ? resistance to carburization and to dry hydrogen chloride and chlorine
  • cracking tubes used in the production of acetic anhydride and ketene – high strength, resistance to both carburization and the formation of sigma phase
  • components, e.g. heat exchangers, piping systems etc., in coal conversion plants
  • steam generator tubing in helium cooled, high temperature reactor systems ? high strength, resistance to helium and to steam

Chemical composition

  Ni Cr Fe C Mn Si Cu P S Al Ti Al+Ti
min 30.0 19.0 bal. 0.06 0.5 0.2       0.30 0.30  
max 32.0 22.0 0.10 1.5 0.7 0.5 0.015 0.010 0.60 0.60 1.2

※The values in the table are for reference only and do not guarantee minimum or maximum values. For further information, please contact us.

Mechanical properties(Round Bar)

  Yield Strength(Mpa) Tensile Strength(Mpa) Elongation(%) Hardness(HB)
ASTM Min Value 170 450 30  
Typical Values at RT 245 559 40 140

Above standard values and typical values of Round Bar.
Please contact us with any questions about reference or value of plate and pipe.
※Grade 1
※The values in the table are for reference only and do not guarantee minimum or maximum values. For further information, please contact us.

International Standard Comparison Chart

  Material Round Bars Plates/Sheets Pipe/Tube
Seamless Welded
ASTM UNS
N08810
UNS
N08811
B408 B409 B407 B163
ASME SB408 SB409 SB407 SB163
JIS NCF800H NCF800HT H4553 G4901 H4552  
DIN 1.4876 1.4959 17460 17460 17459  
Disclaimer
All the information on this website is published in good faith and for general information purpose only and not for technical design purposes. We do not make any warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information on our website is strictly at your own risk. and we will not be liable for any losses and damages in connection with the use of our website.